Beim Lesen der hdparmHandbuchseiten heißt es, dass der -SWert
wird vom Laufwerk verwendet, um zu bestimmen, wie lange (ohne Festplattenaktivität) gewartet werden muss, bevor der Spindelmotor ausgeschaltet wird, um Strom zu sparen
Bei der Konfiguration meiner Laufwerke mit hdparm -B 1 -K 1 -S 120 /dev/sd[d-z]dem Ausgang ist:
setting drive keep features to 1 (on) setting Advanced Power Management level to 0x01 (1) setting standby to 120 (10 minutes) APM_level = 1
Der anfängliche Laufwerksstatus hdparm -C /dev/sd[d-z]ist " aktiv / inaktiv ".
Alle diese /dev/sd[d-z]Laufwerke sind von derselben Marke und demselben Modell, nicht partitioniert, nicht formatiert und nicht gemountet.
Nach 15 Minuten Wartezeit ist der Laufwerksstatus immer noch " aktiv / inaktiv ".
Nur wenn Sie ein "IDE-Laufwerk zwingen, sofort in den Standby-Modus mit niedrigem Stromverbrauch zu wechseln" über hdparm -y /dev/sd[d-z]das Laufwerk ausgeben, wechseln Sie in den Status " Standby ".
Warum wechseln meine Laufwerke nach dem von hdparm angegebenen Zeitlimit nicht in den Standby-Status mit niedrigem Stromverbrauch ?
Einige weitere Laufwerksspezifikationen abgeleitet von hdparm -I /dev/sdd
/dev/sdd:
ATA device, with non-removable media
Model Number: Hitachi HDS5C3020BLE630
Firmware Revision: MZ4OAAB0
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0; Revision: ATA8-AST T13 Project D1697 Revision 0b
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 3907029168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 1907729 MBytes
device size with M = 1000*1000: 2000398 MBytes (2000 GB)
cache/buffer size = 22756 KBytes (type=DualPortCache)
Form Factor: 3.5 inch
Nominal Media Rotation Rate: 5700
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 1
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
unknown 119[7]
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* NCQ priority information
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
416min for SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000cca37dc106a3
NAA : 5
IEEE OUI : 000cca
Unique ID : 37dc106a3
Checksum: correct